Batik


In class we did two different batiks. In each we used a similar method using a mixture of half toothpaste and half lotion. For the first we did a black t-shirt, we were to create a design on the t-shirt using the toothpaste/lotion mixture. I chose to do a tie-dye design and twisted the t-shirt into a spiral and applied rubber bands around it. After that I applied the toothpaste/lotion mixture in various spots on the t-shirt. I then had to set the shirt out to dry. Once the shirt dried we sprayed the shirts in bleach. after the bleach set for a little bit we washed the mixture and bleach off the shirt. Everywhere that was covered in the mixture stayed the same color of the t-shirt and everywhere left blank bleached to an orangish color. Below is my finished product.





The second method we used was with ink instead of bleach. We took a piece of blank cloth and created a design using the mixture. Once the mixture had dried we then applied different colors of ink. Once the ink dried we were able to wash off the extra ink and the mixture off. I think I used too much ink of my cloth because it is very hard to see the areas that were covered by the mixture. I think the t-shirt worked much better than the cloth. below is the finished product of the cloth.


Comments

Post a Comment

Popular posts from this blog

Student Centered Art Problem

Image
For my student centered problem assignment, the problem I chose to solve is creating a hat for benefit. I chose this for two reasons, 1 I wanted to learn to crochet, and two I wanted to create a hat for my grandmother who very recently got diagnosed with breast cancer. I ended up using a hat loom and the hat came out beautifully, unfortunately I don't like the hat loom method as much as I like crocheting, it takes too long and is very tedious. Once I finished creating the loom hat, I created a pompom for it as well. Below is a picture of my finished piece. The Problem: Creating hats for a benefit Materials: Yarn, Loom (if wanted), yarn needle, and crochet hooks Techniques: One technique I learned, is a simple crochet technique. You just crochet a square, connect two ends of the square using slip stitches. Once the slip stiches are done, you take one end of the hat and use a yarn needle to pull extra yarn through the outside to synch the top part of the hat togeth...
Read more

Print Making

Image
For printmaking I did two different types. I did Intaglio and relief/block printing. For the Intaglio we etched plexiglass using baren. First we sketched an image we liked, than we laid the plexiglass over the image and traced over the image using the baren. After, we coated the finished etching in ink and put a piece of paper under it and rolled it through a press. This left us with our finished pieces. The requirement was that we make three finished prints of our sketches. Below are pictures of my finished pieces. Next I did the relief block printing. For this method I made a sketch traced it in charcoal and pressed it onto a soft cut printing block. Once the sketch was transferred I went around the image and cut out pieces of the soft cut block. this created layers so I could transfer my image smoothly. Once the block was cut to my liking, I chose the colored inks I wanted and rolled them onto the block using a brayer. Once covered in ink I just flipped it over and transferred...
Read more

Glass Fusing

Image
Glass Fusing was one of the assignments for my Art Ed Studio course. For this assignment we first explored working with, cutting, and gluing glass. We were first required to create two different fuses, tac and full fuse. With the tack fusing, you fuse the glass but you don't heat it as long so that the pieces dont fuse completely, creating a textured and layered piece. For the full fuse you heat the glass in a kiln for longer, this fuses the glass together fully, creating a piece with a more even layering. After our first day playing around with all the materials and getting the hang of things, we had a whole other assignment. First we were required to do a piece that was fully fused together, with a layer of clear glass to gloss over it. Another part we were required to create a piece with wire in it, for this we glued two pieces of glass together, with a piece of wire in-between. Lastly, we were required to create a slump dish. This is created by making a full fuse glass design...
Read more